Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Blog Article
This article following next about How to Install a Bathtub Yourself is exceedingly engaging. Read it yourself and figure out what you think about it.
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open a wall to eliminate the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the task as well as are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a new bath tub in your washroom if you have actually currently gotten a new bathtub as well as don't need to change the arrangement of your previous water pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with moisture and possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that page on Installing A Bathtub while doing a search on the web. Do you know about somebody who is fascinated about the niche? Take a moment to share it. We take joy in reading our article about Installing A Bathtub.
Schedule And Pricing
Report this page